Solid Carbide Spektra™ Extreme Tool Life Coated Double Straight Flute, Plastic Cutting Router Bits
Used for routing harder and more rigid plastics in the following materials: Acrylic, Acetal, Nylon, PVC, ABS, Corian, Poly (methyl methacrylate) (PMMA), Acrylic Stone, Coroplast®, etc.
THE ONLY Spektra™ Coated Bits – Made in the USA 
Amana Tool® solid carbide router bits provide consistent, repeatable quality. Every tool is guaranteed to match the geometry on the prints, every time on every order. Best control of carbide grades for woodworking, and absolute control of quality standards on all carbide blanks.
Amana Tool Spektra™ bits feature a nACo® nanocomposite coating with an extreme nanohardness and heat resistance. With a brilliant, distinctively-tinted coloring, nACo provides additional improvements in four critical aspects of router tooling.
- nACo coating is an micro-thin ceramic coating which enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality.
- Coatings prevents high heat and oxidation which is detrimental to cutting tool performance.
- Multi-colored hues, while attractive, will dissipate upon use and yet coating will remain fully effective.
- nACo offers approximately 4,500 Vickers for impressive solid hardness on cutting areas of the tool, for an increase up to 2.5 times compared to uncoated bits.
Note: Blue based color dissipates immediately upon use. nACo® nanocomposite coating will not wear off.
Excellent for cutting:
- Plastic
- Acetal
- Acrylic
- Acrylic Stone
- Acrylonitrile Butadiene Styrene (ABS)
- Alupanel®
- Copolymer
- Corian
- Cork
- Coroplast®*
- Corrugated Polypropolyene
- Delrin®
- Epoxy
- Expanded PVC
- Ethylene-Vinyl Acetate
- Foam Board
- Fomex®
- Gatorfoam®**
- High Density Polyethylene (HDPE)
- High Impact Polystyrene (HIPS)
- High Pressure Laminates (HPL)
- Hydroxy-Terminated Polyether (HTPE)
- Low Density Polyethylene (LDPE)
- LubX®
- Lucite
- Mechanical / Engineered Plastics
- Nitrile Rubber
- Nylon
- Perspex® Cast Acrylic Sheet
- Plexiglas®
- Polyethylene (PE)
- Polyethylene Terephthalate (PET)
- Polyethylene Terephthalate Glycol (PETG)
- Poly (methyl methacrylate) (PMMA)
- Polycarbonate
- Polypropylene (PP)
- Polyoxymethylene (POM), also known as Acetal, Polyacetal and Polyformaldehyde
- PVC
- Sign Foam
- StarBoard® (King StarBoard 'R') High Density Polyethylene Sheet (HDPE)
- Styrene-Acrylonitrile
- Styrene-Butadiene Rubber (SBR)
- Styrene-Isoprene-Styrene (SIS)
- Teflon
- Thermoplastic Polyolefin (TPO)
- Ultra High Molecular Weight Polyethylene (UHMWPE)
- Urethane
* Coroplast® is soft plastic cardboard made with super soft, super flexible PVC.
** Gatorfoam® Foam Board, a polystyrene foam board bonded between two layers of Luxcell® wood-fiber veneer.
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
