Cost of Tools	$201.60
Selling Price	$151.20
% Saved	25%

Carbide tipped double edge folding 'V’ groove industrial router bits for shaping Aluminum Composite Materials (ACM) such as Alucobond®, Dibond® and other brands alike. Designed for scoring or cutting the following aluminum/plastic composite materials:

Acetate
Aluminum, Brass, Bronze, Clay, Zinc & Wood Composite Panels
Aluminum 5052
Aluminium Composite Materials (ACM)
Aluminium Composite Panel (ACP)*
ALPOLIC® Copper Composite Material (CCM)
Alcubond®

Alupanel®
Bakelite
Dibond®
Durabond**
e-panel™
Etalbond®
Nylon

PE and FR Cores
Phenolics
Plastic/Acrylic
Plexiglas®
PVC
Titanium Composite Material (TCM)
Wood

Aluminum Composite Panel (ACP) is a type of ACM flat panel that consists of two thin aluminium sheets bonded to a non-aluminium core and is widely used as cladding for many diverse applications such as interior and exterior office buildings, external cladding or facades of buildings, hospitals, convention centers, airports, hotels, insulation and signage. **Durabond is a polyethylene core with 0.3mm colored aluminum sheet on either side, pre-finished requiring no decoration.

Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding the remaining material by hand.

Specially designed router bits are used to route V-grooves in the above materials to allow easy bending without cracking the bent area. Route within 0.8mm from the bottom of the composite panel to achieve a clean bend/radius. Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding the remaining material by hand. Ideal for wall panel fabrication.

For use on routers and CNC machines
Industrial quality, carbide tipped

ACM panels may be used both indoors and outdoors. Ideal for wall panel fabrication
RPM: 18,000-24,000 (*Feed rate should be 120 inches per minute.)

Benefits of ZrN Coating:

Optimized flute geometry and low Total Indicated Runout (TIR) guarantees clean cuts, essentially eliminates sanding and reduces chatter when used with low TIR spindles
Creates a harder and tougher cutting ceramic over carbide edge, allowing for a prolonged cutting edge life and helps to prevent the build-up/galling of material in the flutes while cutting

Has the ability to run and/or be spun much faster than uncoated tools
High aspect ratio for single pass deep-reach cutting
High flute volume supports high feed rates and chip loads.
Flute geometry optimized for cutting sign foam, sign board, hardwoods, thermoplastics and phenolic composites

Set #AMS-213 Includes the Following Tools:

Tool No

Description

Product Page

45745

90º x 0.090" Tip x 1/2" Dia x 1/4 Shank V-Groove Double Edge Folding for ACM Router Bits

View Details

45795

108º x 0.090" Tip x 1/2" Dia x 1/4 Shank V-Groove Double Edge Folding for ACM Router Bits

View Details

51402-Z

Solid Carbide CNC Spiral 'O' Flute, Aluminum Cutting 1/4" Dia ZrN Coated Router Bit

View Details

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood .

3-Pc Aluminum Composite Material (ACM) 90, 108 Degree and 1/4 Inch Diameter, 1/4 Inch Shank Pack

Set #AMS-213 Includes the Following Tools:

You May Also Want...